The corrosion behavior of sputter-deposited aluminum-tungsten alloys

Thin films on aluminum-tungsten alloys were prepared by co-deposition of pure aluminum and pure tungsten, each sputtered by an independently controlled magnetron source, on glass and sapphire substrates. Completely amorphous films were obtained in the Al₈₀W₂₀-Al₆₇W₃₃ composition range. Passivity and corrosion behavior of amorphous Al-W alloys were investigated in 1 M deaerated hydrochloric acid solution using polarization and impedance spectroscopy measurements and have been correlated with the properties of pure alloy components. Tungsten and sputter-deposited Al-W thin films are inherently passive materials while aluminum undergoes pitting corrosion in hydrochloric acid solution. The passive film formed at the OCP on each alloy possesses excellent electric and dielectric properties comparable to those of the isolating film on tungsten. The absolute impedance increases with increasing tungsten content in the alloy. According to electrochemical polarization measurements, alloying Al with W in solid solution significantly enhances the material's resistance to pitting corrosion by shifting the breakdown potential above 2000 mV (Al₆₇W₃₃) and lowering the corrosion rate at the OCP by more than two orders of magnitude. The most likely mechanism explaining the passivity of amorphous Al-W alloys, the Solute Vacancy Interaction Model (SVIM), involves the formation of complexes between highly oxidized solute atoms (W⁺⁶) and mobile cation vacancies, which restrict the transport of Cl⁻ through the oxide film and inhibit its breakdown in hydrochloric acid solution. The role that film stress relaxation effects and microscopic defects in amorphous Al-W films, of the some composition, and deposited on various substrates play in their corrosion resistance is discussed.     

The availability of daylight from tropical skies—a case study of Malaysia

In Malaysia, no long-term daylight data are measured. It was only recently that the need to measure the availability of daylight became urgent when the importance of daylighting in buildings was rediscovered. The hourly daylight availability has been simulated for the Malaysian sky using daylight modelling techniques based on empirical and measured solar irradiation and cloud cover data. This paper presents the techniques involved in producing exterior illuminance data. These data were then compared with measured illuminance at Shah Alam and Bangi, Malaysia. The global illuminance levels are generally high, with values exceeding 80,000 lux at noon during the months when solar irradiation is highest. Even during the months when the ground receives less solar irradiation, the peak illuminance can reach 60,000 lux. Applications and uses of such data are in daylighting design, both for visual and thermal comfort, task illuminance and energy-conscious design of buildings. Recommendations are made at the end of the paper on the various climatic data that are required to be measured for overall daylighting design applications.     

Nondestructive evaluation of the characteristics of degraded materials using backward radiated ultrasound

The frequency dependency of Rayleigh surface wave is investigated indirectly by measuring the angular dependency of the backward radiation of the incident ultrasonic wave in two kinds of degraded specimens by scuffing or corrosion. Then, the frequency dependency is compared with the residual stress distribution or the corrosion-fatigue characteristics for the scuffed or corroded specimens, respectively. The width of the backward radiation profile increases with the increase of the variation in residual stress distribution for the scuffed specimens. In the corroded specimens, the profile width decreases with the increase of the effective aging layer thickness and is inversely proportional to the exponent, m, in the Paris’ law that can predict the crack size increase due to fatigue. The result observed in this study demonstrates high potential of backward radiated ultrasound as a tool for nondestructive evaluation of subsurface gradient of material degradation generated by scuffing or corrosion.     

Top-Seeded Melt-Growth of YBa2Cus3Ox Crystals for Neutron Diffraction Studies

We have grown cubic centimeter-size crystals of YBa₂Cu₃O _x suitable for neutron studies, by a top-seeded melt-growth technique. Growth conditions were optimized with an eye toward maximizing phase purity. It was found that the addition of 2% Y₂BaCuO₅ and 0.5% Pt (by mass) were required to prevent melt loss and to obtain the highest crystallinity. A neutron diffraction study on a mosaic of six such crystals found that the final Y₂BaCuO₅ concentration was 5%, while other impurity phases comprised less than 1% by volume. The oxygen content was set to x = 6.5, the crystals were detwinned, and then carefully annealed to give the well-ordered ortho-II phase. The neutron study determined that 70% of the mosaic's volume was in the majority orthorhomic domain. The neutron (006) and (110) rocking curve widths were ～1° per crystal and ～2.2° for the mosaic, and the oxygen chain correlation lengths were >100 Å in the a- and b-directions and ～50 Å in the c-direction.     

Inertia effects on non-parallel thermal instability of natural convection flow over horizontal and inclined plates in porous media

The inertia effect on the onset of thermal instability in natural convection flow over heated horizontal and inclined flat plates embedded in fluid-saturated porous media is analyzed. The linear non-parallel flow model is employed in the instability analysis, which takes into account the streamwise variation as well as the transverse variation of the disturbance amplitude functions. The set of partial differential equations for the disturbance amplitude functions are converted to a system of homogeneous linear ordinary differential equations with homogeneous boundary conditions by the local non-similarity method. The resulting eigenvalue problem is then solved by an implicit finite-difference method. Representative neutral stability curves and critical Rayleigh numbers are presented. It has been found that as the angle of inclination relative to the horizontal increases, the surface heat transfer rate increases, whereas the flow becomes more stable to the vortex mode of instability. Also, as the inertia effect, expressed in terms of Forchheimer number, Fr, increases, the heat transfer rate decreases, but the flow becomes more stable. It is demonstrated that the non-parallel flow model predicts a more stable flow than the parallel flow model.     

High-resolution electron microscopy of the twinning and intergrowth in Ca4Al6SO16 and Ca3SrAl6SO16

The microstructures of unhydrated calcium aluminosulphate Ca₄Al₆SO₁₆ and Ca₃SrAl₆SO₁₆ have been studied by high-resolution electron microscopy (HREM). The results showed that twinning and twinned slabs could be introduced taking the [1 1 2] direction as the twin axis so that it seems to be coincident with the law of twinning formed in body-centred cubic structures. A previously reported superlattice with a repeat period twice that of the fundamental structure along the 〈1 1 0〉 direction has also been found in both matrix and twin variants. The close intergrowth of Ca₃SrAl₆SO₁₆ and another phase, possibly Sr₃Al₂O₆ existing as an inclusion between these two twin variants, was determined and clearly revealed by electron diffraction and HREM images. The coherent interphase boundaries and orientation relationship between them can also be deduced.     

Determination of molecular weight distributions of tert-octylphenol ethoxylate surfactant polymers by laser desorption Fourier transform ion cyclotron resonance mass spectrometry and high-performance liquid chromatography

Triton polymers are commercial surfactants whose molecular weight distributions are conventionally determined by means of high-performance liquid chromatography (HPLC). However, in the case of the important octylphenol ethoxylates [p-C8H17-C6H4-O-(CH2CH2O)n-H], HPLC cannot resolve individual oligomers of high molecular weight Triton surfactants (e.g., greater than 2000 u or so; u = unified atomic mass unit). In this paper, we show that laser desorption Fourier transform ion cyclotron resonance mass spectrometry (LD/FT/ICR/MS) provides a simple and accurate measure of such Triton surfactant molecular weight distributions up to at least 3500 u, based on a single-shot laser pulse measurement of a few seconds duration. Comparison of LD/FT/ICR/MS and HPLC molecular weight distributions of low molecular weight surfactants shows that laser desorption/ionization produces minimal fragmentation and thus offers an accurate measure of the relative abundances of the neutral oligomers, without the need for prior chromatographic separation of the components. Moreover, for all Triton polymer molecular weight distributions (700-3000 u), LD/FT/ICR/MS provides much more highly resolved profiles of oligomer relative abundances. Finally, LD/FT/ICR/MS reveals the presence of poly(ethylene oxide) side products of the polymerization process, which are not observed by HPLC with conventional ultraviolet absorption detection.